Front Disk Brake Conversion & Rear Adj
guayule100 > albums
-
punching out studs
- last edit: Mon Apr 21 08:14:52 PDT 2008
- comments: 0
-
freed hubs
- last edit: Mon Apr 21 08:15:06 PDT 2008
- comments: 0
-
New Scandix disc brake rotor
- last edit: Mon Apr 21 08:15:33 PDT 2008
- comments: 0
-
PV 444 brake hub fits on the Scandix 1800 disc rotor
- last edit: Tue Feb 28 08:35:19 PST 2006
- comments: 0
-
machined a cutaway on the hub
- last edit: Mon Apr 21 08:16:11 PDT 2008
- comments: 0
-
finding the right studs was a little tricky
- last edit: Tue Feb 28 08:35:53 PST 2006
- comments: 0
-
seating studs
- last edit: Tue Feb 28 08:36:05 PST 2006
- comments: 0
-
seatingstuds
- last edit: Sun Apr 22 09:59:44 PDT 2007
- comments: 0
-
measuring that 1 inch of each stud protrudes
- last edit: Tue Feb 28 08:36:15 PST 2006
- comments: 0
-
new disk rotors mounted
- last edit: Tue Feb 28 08:36:36 PST 2006
- comments: 0
-
used caliper Mount off the 1800
- last edit: Mon Apr 21 08:17:14 PDT 2008
- comments: 0
-
drivers side mount - 3 holes plug welded
- last edit: Mon Apr 21 08:17:49 PDT 2008
- comments: 0
-
punching new mount hole locations
- last edit: Mon Apr 21 08:18:33 PDT 2008
- comments: 0
-
Modified drivers side caliper mount
- last edit: Mon Apr 21 08:19:09 PDT 2008
- comments: 0
-
new loaded calipers
- last edit: Mon Apr 21 08:19:50 PDT 2008
- comments: 0
-
piston crossover line
- last edit: Mon Apr 21 08:29:38 PDT 2008
- comments: 0
-
grinding calipers
- last edit: Mon Apr 21 08:21:14 PDT 2008
- comments: 0
-
with caliper installed
- last edit: Tue Feb 28 08:37:43 PST 2006
- comments: 0
-
the piston crossover line is also installed
- last edit: Mon Apr 21 08:28:58 PDT 2008
- comments: 0
-
drivers side caliper mounted
- last edit: Mon Apr 21 08:34:28 PDT 2008
- comments: 0
-
passenger side top shock mount bolt switched to front
- last edit: Mon Apr 21 08:28:06 PDT 2008
- comments: 0
-
the lower bolt had to be modified, first by sawing it
- last edit: Mon Apr 21 08:27:46 PDT 2008
- comments: 0
-
grinding the lower shock mount bolt
- last edit: Tue Feb 28 08:44:43 PST 2006
- comments: 0
-
and finally welding it at a ~30 degree angle
- last edit: Mon Apr 21 08:27:26 PDT 2008
- comments: 0
-
Carlos inspecting the setup
- last edit: Sat Jan 20 09:39:29 PST 2007
- comments: 0
-
Drivers side shock relocated to front
- last edit: Mon Apr 21 08:27:02 PDT 2008
- comments: 0
-
master cylinder dissassembled
- last edit: Mon Apr 21 08:25:27 PDT 2008
- comments: 0
-
master cylinder proportioning valve
- last edit: Mon Apr 21 08:35:57 PDT 2008
- comments: 0
Album Description:
checking axial shaft end play
Album Info:
Album Stats:
- Photos: 48
- Views: 10271
- Downloads: 2
No comments so far...
To be able to leave a comment please Log in or Sign up.